Moxa IOLOGIK W5340-T Manual de usuario Pagina 68
- Pagina / 196
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
ioLogik Cellular Micro RTU Controller Utility: ioAdmin
3-37
ISAKMP phase 2
Encryption mode: Select the VPN ISAKMP phase 2 encryption mode.
Authentication mode: Select the VPN ISAKMP phase 2 authentication mode.
Diffie-Hellman group: Select the VPN ISAKMP phase 2 DH group. Increasing the DH Group number increases
the level of encryption implemented for PFS.
SA life time (default = 28800): Enter the number of seconds for the VPN ISAKMP phase 2 Lifetime, which
is the period of time that passes before establishing a new IPSec security association (SA) with the remote
endpoint.
Advanced Settings
Anti-replay: Anti-replay is the method of not allowing an intercepted packet message to be sent to the
recipient multiple times without the original sender knowing (default = Disable).
Dead Peer Detection (DPD): Enable or disable the Dead Peer Detection. DPD is a method of detecting a dead
Internet Key Exchange (IKE) peer. It sends a DPD packet to the peer every 60 seconds with no traffic and
attempts to connect normally. If the DPD packet fails 5 times the VPN will continuously re-establish a
connection (default = Disable).
VPN System Log Events and Error Codes
VPN system log Description
UNLINK_TIME_REACH SA Lifetime timeout
UNLINK_TIME_OUT No response from remote VPN server
UNLINK_NO_PROPASOL The remote VPN server does not have matched VPN settings(proposal)
UNLINK_DPD DPD detecting
IKE_PHASE1_MAIN_START IKE phase1 Main mode starts
IKE_PHASE1_AGGR_START IKE phase1 Aggressive mode starts
IKE_PHASE1_ENCRY_START IKE phase1 VPN tunnel encrypting
IKE_PHASE1_OK Passing the VPN tunnel phase1
IKE_PHASE2_OK Passing the VPN tunnel phase2
IKE_RENEW_START Rekeying
IKE_RENEW_OK Rekey successfully
PHASE1_TIME_REACH Phase1 SA lifetime timeout
OLD_SA_TIME_REACH Earlier SA lifetime is deleted by the ioLogik
REMOTE_DEL_ISAKMP Key of VPN tunnel phase1 is deleted by the remote
REMOTE_DEL_ESP Key of VPN tunnel phase2 is deleted by the remote
REMOTE_DEL_ESP_OLD Earlier SA lifetime is deleted by the remote VPN Server
Cellular Reconnection
Carriers disconnect idle mobile device connections in order to save bandwidth for other on-line users and
applications. To keep the ioLogik W5300 Always On, the ioLogik W5340 must not only have the capability to
detect the cellular connection and reconnect to the network once it is disconnected, but also needs to send out
signals (ICMP package) to notify carriers that the ioLogik W5340 is still alive.
- User’s Manual 1
- Table of Contents 3
- Introduction 6
- Quick Start Guide 7
- Architecture 7
- Product Features 10
- Appearance 10
- Package Checklist 11
- Product Selection Guide 12
- Product Specifications 12
- Getting Started 17
- Before Testing 18
- Laboratory Testing 19
- Configuring the DIO Channels 23
- Digital Output (Sink Type) 24
- Testing the I/O Device 25
- DIN Rail / Wall Mounting 26
- Network 28
- Detailed instructions: 29
- IP Address 30
- Export System Config 31
- Import System Config 31
- Utility: ioAdmin 32
- Features of ioAdmin 33
- Main Screen Overview 34
- Menu Bar 34
- Menu Bar: File 34
- Menu Bar: System 35
- Menu Bar: Sort 38
- Quick Links 38
- Menu Bar: Help 39
- Navigation Panel 40
- Main Window 41
- Server Info Panel 41
- Sync. rate status 42
- Status bar 42
- Server Settings Panel 43
- LAN Settings Panel 44
- I/O Configuration Panel 45
- Configuring Virtual Channels 47
- Configuring DIO Channels 49
- Counter Scaling 50
- Relay Count Monitoring 52
- Testing DI and DO Channels 53
- I/O Expansion Panel 54
- Active Tags Panel 57
- Active OPC: Redundancy Mode 58
- Heartbeat Interval 58
- Read/Write Privilege 59
- Active Tags 59
- Cellular Settings Panel 61
- Caller IDs 62
- Operation Mode Setting 62
- DDNS Settings 63
- Port Forwarding 64
- General Settings 65
- Manual Key/ESP 66
- ISAKMP/PSK 67
- Cellular Reconnection 68
- Meter/Sensor 70
- Network Statistics 71
- Watchdog Panel 72
- Click&Go Logic Panel 72
- Click&Go Logic 74
- Overview 76
- Click&Go Logic Basics 77
- Working with Rules 78
- I/O Configuration 79
- Analog Input Mode Selection 81
- Alias Name Configuration 81
- Testing the I/O Channels 82
- Defining Global Variables 83
- SNMP Trap Server 84
- E-Mail Server 84
- Active Message Server 86
- SMS Phone Book 86
- Working/Off Working Days 87
- FTP Settings 87
- Data Logging Profile List 88
- Working with Logic 91
- IF “A” THEN “B”, ELSE “C” 92
- IF Conditions 93
- Virtual Channel 95
- Relay (Counter) 95
- Schedule 97
- System Start-up 98
- THEN/ELSE Actions 100
- Counter 101
- Pulse Output 102
- Relay (Counts) 103
- Internal Register (Integer) 104
- SNMP Trap 105
- Active Message 105
- ATTENTION 105
- Short Message Service 107
- Data Log Start/Stop 108
- FTP Service 109
- Activating the Rule-set 110
- Import/Export Configuration 110
- Planning and Assistance 112
- Internet 120
- Statistics 122
- Log Profile Creation 124
- Log File upload with FTP 126
- Connecting to a SCADA System 130
- Setup Procedure 132
- Wake on Call 139
- Pin-outs and Cable Wiring 141
- Pinouts 142
- Cable Wiring 144
- Digital Output Sink Mode 145
- Relay Output 145
- Analog Input 145
- SMS Commands 146
- SMS Command Syntax: 147
- SMS Command Table 147
- Local I/O Commands: 148
- Expansion I/O Commands: 149
- Option Commands: 150
- Modbus/TCP Address Mappings 151
- Modbus Mapping 152
- Factory Default Settings 192
- Connection 194
- Cellular modem error codes: 195
- Service delay time 196
Relacionado con productos y manuales para Dispositivos de redes celulares Moxa IOLOGIK W5340-T
(105 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales